What is driving the demand
In February 2026, The Shaw Group announced a pipe fabrication scope for a West Texas data center: about 68,730 linear feet of carbon-steel piping in 4,582 prefabricated spools, from NPS 2 to 24 inches with an average of NPS 10.5.
The same month, Associated Builders and Contractors estimated that construction must add 349,000 workers in 2026, citing megaprojects such as AI data centers. More spools and fewer hands push contractors toward repeatable machine prep in the shop.
Where pipe end preparation slows a spool shop
Torch cutting leaves a heat-affected zone and oxide that must be ground off before welding, and hand grinding varies from one fitter to the next. Cold cutting with a pipe beveling machine produces a machined end ready for fit-up, so the welder starts on a consistent bevel and land on every spool.
TABLE 1 Split frame models for NPS 2-24 spools
| Model | OD range | OD inch | Wall: standard / heavy duty | Rotation |
|---|---|---|---|---|
| TOE-168 | 50-168 mm | 2-6 in | 30 mm / - | 18 r/min |
| TOE-325 | 168-325 mm | 6-12 in | 30 mm / 110 mm | 13 r/min |
| TOE-457 | 300-457 mm | 12-18 in | 30 mm / 110 mm | 12 r/min |
| TOE-610 | 457-610 mm | 18-24 in | 30 mm / 110 mm | 11 r/min |
Two pipe bevelling machine formats from our range
OD-Mounted Solution
Our TOE-457 split frame pipe cutting and beveling machine splits in half and clamps around the pipe OD. It cuts and bevels in-line pipe or open ends simultaneously and also performs counterbore and flange facing. The electric TOE drive is rated 200-240 V at 50-60 Hz.
ID-Mounted Solution
The ISE ID-mounted pipe beveling machine locks inside the bore with expanding mandrel blocks. Its T-shaped body needs minimal radial space, and it faces and bevels pipe ends and flanges in U, single-V, double-V and J profiles. The ISE-30 weighs only 10 kg.
TABLE 2 OD-mounted vs ID-mounted comparison
| Item | OD-mounted split frame (TOE) | ID-mounted (ISE) |
|---|---|---|
| Mounting | Around the pipe OD, split frame | Inside the bore, expanding mandrel |
| Series range | 25-1230 mm OD | 18-820 mm ID |
| Wall thickness | Up to 30 mm standard, 110 mm heavy duty | Up to 15-75 mm by model |
| Operations | Cut, cut and bevel together, counterbore, flange facing | Facing and bevelling of pipe ends and flanges |
| Bevel profiles | Angle per request, single or double tool head | U, single-V, double-V, J |
| Drive | Electric, pneumatic or hydraulic | Electric or pneumatic |
| Typical spool task | Cut to length and bevel in one setup | End prep on cut ends and flanges |
| Product page | View TOE-457 | View ISE series |
? Buyer FAQ
Can a pipe bevelling machine cut and bevel at the same time?
Yes. Our OD-mounted split frame machines cut and bevel simultaneously, leaving a cold-machined end ready for welding.
Which model covers 10-inch spools?
NPS 10 pipe has a 273 mm OD, inside the 168-325 mm range of the TOE-325.
Will the machine run on 60 Hz power?
The electric TOE drive is rated 200-240 V at 50-60 Hz. Other supplies can be built to order.
Factory-direct support
As the manufacturer, we have built weld preparation machines since 2004 and export to more than 50 markets. Send us your pipe OD range, wall thickness, material and bevel drawing, and our engineers will match frame size, drive and tooling before quotation.
Post time: Nov-18-2026